How to remove ohm super cylinder speaker can

How to remove ohm super cylinder speaker can

How to remove ohm super cylinder speaker can

Introduction

As we all know that the speaker can be having quality sound at home but it will get to a time that the speaker cylinder can is preventing quality sound from getting into due to several reasons that you can fix. At some point the cylinder can be old enough that you need to remove and replace with another one.Therefore, if you any of the issues, then you need to find out what you need to do to make the process successful such that you will remove the cylinder can and fix back properly. In this case you can consult a professional to help remove and fix back the cover.

Below are the steps you can follow when removing the ohm super cylinder speaker can and how you can fix it back when you are replacing or when checking for an issue to fix then fix back the cover. Later are the frequently asked questions and the conclusion.

How to remove ohm super cylinder speaker can

Materials needed

Screwdriver

Paint scraper

Towels

Acetone

Marker

New foam for replacement

Speaker repair glue

Masking tapeCable ties

Steps to remove the cylinder speaker can

Remove the speaker from the cabinet

The speaker has some screws that hold it to the cabinet that you need to use the screwdrivers to unhook the screws within it. After removing the screws, displace the speaker from cabinet using any tool or use your hands with some energy to displace it.

Check if the speaker ahs a ring underneath since some few speakers have it that they contain wires that you need to be keen with.Remove the current foam it contains.Using acetone and a piece of cloth or cotton wool, rub the surface with the foam until it goes off. And if it fails add more acetone give it some time to stay on the surface then later rub it with more energy. After removing the foam, there is a ring that you will need to remove too. At this point, you need to use the screwdriver to take it off from the surface. While removing the ring, you get to damage the cardboard that you have to replace it. After that remove the foam below it by adding more acetone and let it soak then rub it lightly.Make a circle to show the new place for the foam.Ensure you draw a circle at the surface to show the new place to fix the new foam after removing the cylinder.

Consider using any round tool that will guide you to make a good circle. Shim the voice coil.Remove the dust cap by cutting it carefully at the centre of the speaker cone with a sharp object. Ensure you are careful to avoid damaging the voice coil of the speaker.

Shim in this case brings the label sheets that you need to get the accurate size for a fine surface for the foam when fixing back the speaker. Apply glue on the speaker cone.it is good to apply glue on the surface of the speaker cone in order to dry and make sure the surface is clear and stick two parts for a good period. Get new foam to fix on the speaker cone.Carefully secure new foam to fix on the surface after applying glue on it. When fixing the foam, ensure you are close to the surface so that you can put right in its place such that after sticking it with the glue you are again removing it from the place. When adjusting the position, ensure you move it carefully so that you can maintain the uniform circle.After fixing the foam to its exact place, tap every part of the foam to ensure the glue on the board soaks inside it.

Apply some piece of tape on the foam after soaking the glue in it to enhance the stickiness of the foam. Apply the tape thrice on the foam until you feel with your hands that everything is tight. Give the glue time to stick to the foam.The time you will leave the glue, tape and foam to have depends with the amount of glue you used in the process. If you applied more glue you need to give the glue more time to dry. Remove the tape from the foam.When removing the tape, be gentle and release it carefully to avoid yanking it off that destroys the surface of the foam. Consider peeling the tape on its side but not direct on top of the foam. Repeat the process with all the pieces of tape you applied to the foam that in case you remove the tape and peels off with the foam you need to fix a new tape so that the foam sticks. Fix a new ringApply glue again at the edge of the speaker to fix a new ring, therefore, lift the foam gently and fix the ring. If the speaker has a cardboard you need to replace it too but if it lacks then you are good to go. Allow the glue to dry.With this step you need to give a whole night for the glue to dry properly such that you need to turn the speakers upside down and fix the speakers using cable ties to tighten them. After drying of the glue, you can now remove the shim and reglue the dust Fix back the speaker to its place.If you are removing the ohm cylinder speaker can to check for an issue, you can fix back everything in place.

Conclusion

The article above shows the steps of removing the ohm super cylinder speaker can that there are many steps you need to follow since a speaker has several wires that connect together to produce the sounds such that you need to be keen with each step to avoid destroying some parts of the system.It is good to check the manufacturers manual on the tips of handling the speakers and their cans since different speakers have different materials on their surfaces that some are delicate and need proper care.


Franklin Obibo

48 Blog posts

Comments